Customer ratings for Set of 2 McGrey SPS-1 Speaker Stand Steel with bag

I received a fast delivery. Product is very good for the price. Gladly again

Excellent product, robust, good price.

all great, super goods, fast delivery, top, gladly again

Everything super fast delivery, one can further empfeheln

Pleasantly surprised by the quality of these feet. Good section of the tubes, easy adjustments. Very fast delivery. The price really interesting. I discover Kirstein, they seem to offer good material.

Item was delivered quickly as promised. Stands very stable. Clear buy recommendation

Well made and easy to use. Fit perfectly.

But at first glance, it seems to correspond to my expectations! See with time, but you don't leave much time to have an opinion...

The best judgement you can elicit from a North German !

I had the tripods now twice in use, perform semi-professionally as a singer and needed a quick, inexpensive solution. The tripods are super stable and still nice and light, so I can transport them well alone without having to gain muscle mass ;-P I'm still waiting to see how it looks in a few months after repeated assembly and disassembly, but now they make a great impression in any case - and unbeatable for the price!

Two speaker stands in good steel construction with foldable tripod and telescopic tube that can be extended in steps. The telescopic tube has a Ø of 35 mm and is thus designed for standard flanges (Ø36 mm). The telescopic tube can be extended in 6 steps and is secured by a pin hanging from a strap. With horizontally adjusted tripod struts, the telescopic height of 127 cm can be extended in steps from 12.5 cm to 189 cm. Then tighten the clamping screw of the immersion tube. If you tighten the clamping screw a little bit by hand, you will have some play in the telescopic tube. So tighten carefully courageously a little more firmly ....... and, what is the ????? the clamping screw turns over. First of all everything back and examine ...... well, there we have the problem. For the clamping a pressure piece of not too firm plastic is used. In this pressure piece a nut M8 with 12er SK (hexagon) and 5 mm thickness is inserted. For clamping via the corresponding screw, the nut pushes itself out of the clamping piece and should, however, make a positive torque transmission via the SK. The SK in the push piece is designed as a 13 SK. When tightening, the relatively short nut now slips to the edge of the pressure piece and then turns over with respect to the chamfer and the mismatched SK. Well, sh.... Play, in the truest sense of the word. Since I like the tripods in the overall concept, so first off to the workshop and fetched matching nuts in M8, 13 SK and 6.5 mm thickness. The nut fits snugly in the SK and still disappears easily in the countersink ..... there should actually be a 8 mm thick nut, but there's not so. Well, assembled and now the clamping works. I also checked the clamping of the tripod ....... same too small nut, different function principle. The nut should be supported for torque transmission only on two surfaces of the SK and that in plastic. So also here the nut exchanged. Here, the clamping is then ultimately via a pressure surface, which then presses against the dip tube and thus sets the tripod. In principle the clamping is functional, but with the not defined plastic ..... oh, oh ..... hopefully not so'n "Chinamix" which becomes brittle. Otherwise, the tripod stands with its 35er tubes with an approximately Ø 1m projection quite stable. At the ends rubber caps are attached as feet.
Finally, one must operate the clamping only for the up - and dismantling, but that just with some attention. I hope once that the long-term use, the general impression does not cloud.
So, as an overall impression I can only refer to the heading.

For the price you can not say anything, I find the product sufficient

These box stands fully serve their purpose and are really stable despite the low price.

For this price, the tripods are very good, I would not have expected.
Thanks

super price good and safe stand simply great

Simple but solid design without visible corners and edges. First make a good EIndruck. Let's see how they do in the occasional gig everyday with 12 kg active boxes.

The tripods make a solid impression at first glance, no sharp edges, everything is well painted. For the price really okay - however, you also have no hard use behind me yet, where the central plastic star or the rivets of the connections were stressed.

Absolutely satisfied! These speaker stands can keep up with those from higher price segment!!!!

Given the price, I had not expected too much in terms of quality. But I was taught better. We verweden the tripods in the rehearsal room and since then our small PA stands bombproof.
Ruckzuck up and dismantled again and can be stored very space-saving.

5 stars, because price / performance simply unbeatable.
Absolutely not intended for live use, but for the rehearsal room fully sufficient and stable enough.